LashesStep-by-step practice·Lesson 30/58·4:40
Volume lashes: making fans step by step
A volume set with handmade fans: prep as in the classic lesson, setting up the station, picking a few lashes off the strip, sliding the tweezer to open the fan and close its base, checking the fan, touching only the base into the glue, isolating one natural lash, placing the fan so it wraps the lash 0.5–1 mm from the lid, alternating zones, checking for stickies, finishing and clearing up.
The narration is in Vietnamese (subtitles: CC button on the player). The steps below are in English.
Safety first
Distances, thickness and lashes per fan here are general trade guidance; always follow the lash maker's chart and the glue maker's instructions (humidity, temperature, how long to keep lashes dry). The client's eyes stay closed throughout, and glue must never touch the skin. Rules on beauty services and products differ by country. This is a training aid, not a licence.
These videos are study aids. They don't replace supervised hands-on training and they are not a professional licence. Always follow the product manufacturer's instructions and the rules where you work.
Key points to remember
- 1
Prep as in the classic practice lesson: consultation and allergy questions, client comfortable, lashes cleansed, under-eye pads, lashes brushed. While brushing, read the natural lashes zone by zone to choose how many lashes per fan.
- 2
Station: a tile of volume lashes (very fine) sorted by length, a jade stone with a fresh drop of glue, a straight tweezer for isolating and an angled volume tweezer for making and placing fans, single-use items; the glue bottle closed straight away.
- 3
Picking: lay the volume tweezer tip across a few lashes on the strip, towards the tips; take exactly the number you need, grip very lightly, and work in from the edge of the strip.
- 4
Opening the fan: slide the tweezer slowly towards the base so the lashes spread (some roll or tilt the tweezer instead); close the tweezer at the base so it is narrow and neat, then lift the fan off. Don't spread it too wide.
- 5
Check before the glue: narrow, closed base, lashes evenly spread and symmetrical, the right number of lashes. A lopsided fan, a wide base or two lashes stuck together: discard it and make a new one.
- 6
Glue: touch only the base of the fan into the edge of the drop and draw it out; don't dip deep or let glue creep up between the lashes. A fan with a big blob of glue goes in the bin. Replace the drop often, as the glue maker advises.
- 7
Isolate exactly one natural lash with the straight tweezer, cleanly, as in the classic lesson — a fan is wide, so one lash left close by will be caught.
- 8
Placing: the base wraps the natural lash, in its growth direction, about 0.5–1 mm from the lid, never on the skin; press lightly, hold still until the glue grabs, then release. If it sits crooked, remove it at once before the glue sets.
- 9
Alternate zones (outer, middle, inner) so the glue has time to dry; after each zone run the tweezer from base to tip to check for stickies and separate them at once. Short and light at the inner corner, gradually longer towards the outer corner (styles: the lash-mapping lesson).
- 10
Finish: brush and compare both eyes, remove the pads while the eyes are still closed, open slowly; aftercare as in the classic lesson and book a refill in about 2–3 weeks. Single-use items into a lidded bin; tweezers cleaned and disinfected after every client.
Tips
- Remaking a fan takes seconds; putting a bad fan on a client's eye costs far more. Practise making fans on a tile every day until they are even; speed comes after that.
- Your first volume sets will take much longer than classic. In VaraaAi, set the volume service duration to each technician's real pace so the calendar doesn't overrun.
Quick quiz
3 questions, 20 points for each right answer.
When picking up glue, which part of the fan touches the drop?