NailsTheory & experience·Lesson 15/68·5:12
Acrylic: understand it for lasting, safe nails
How acrylic sets without a lamp, the liquid-to-powder ratio — beads too wet and too dry —, nail structure (stress area, apex, C-curve), primer, why acrylic lifts, vapour and dust, MMA, allergy, infills and removal.
The narration is in Vietnamese (subtitles: CC button on the player). The steps below are in English.
Safety first
Acrylic liquid has a strong vapour and is flammable: local exhaust at the table, ventilation, no flames, lids on. Ratio, primer and times always follow the brand's instructions. Liquid and unset product must never touch the skin. Rules differ by country and city.
These videos are study aids. They don't replace supervised hands-on training and they are not a professional licence. Always follow the product manufacturer's instructions and the rules where you work.
Key points to remember
- 1
Acrylic has two parts: the liquid and the powder. When the wet brush touches the powder the reaction starts at once in the air, with no lamp, and the bead sets within minutes — so place and press it decisively.
- 2
The liquid-to-powder ratio matters most. A good bead is moist, glossy and round, holds its shape and only settles a little. Every brand has its own ratio; practise on training nails before working on customers.
- 3
A bead that is too wet runs, floods the side walls and cuticle, sets slowly and is weak; unreacted liquid can sit on the skin and lead to allergy. A bead that is too dry is grainy and porous, crumbles at the edge, grips poorly and stains.
- 4
Structure as for builder gel: thin at the cuticle and the tip, thickest at the apex over the stress area (where the nail leaves the bed, slightly behind it), an even C-curve and straight side walls. The longer the extension, the more the structure matters.
- 5
Adhesion comes from prep: dry prep, remove the cuticle tissue from the plate, take off the shine, clear dust and oil. Primer (acid or acid-free) goes on very thinly, on the nail plate only — never on skin, which it can burn; use it as the brand says.
- 6
Lifting usually comes from poor prep, too little or too much primer, product on the skin, a thick edge at the cuticle, a dry bead or a missing apex. Never cover a lifted area: file it away first, then infill.
- 7
The liquid's vapour is strong and flammable. The City of Helsinki's hygiene guidance: where acrylic nails are done, the workstation must have sufficiently efficient local exhaust ventilation, and filing dust must be extracted locally too. Wear a mask when filing.
- 8
Pour a small amount of liquid, enough for one customer, into a dappen dish with a lid and cover it when not in use; close the bottle at once, away from flames. Leftover liquid never goes down the sink — dispose of it as the product's safety data sheet and local waste rules say.
- 9
MMA: the US FDA had liquids made of 100 % MMA taken off the market after injuries to nails and skin; Germany's BfR advises manufacturers not to use MMA in powder–liquid systems. Professional liquids usually use other monomers such as EMA. Buy only clearly labelled products with a safety data sheet.
- 10
Infill usually every 2–3 weeks, as the apex moves forward with growth. Be honest: acrylic is strong, but the natural nail underneath needs care — no prying. Removal: acrylic soaks off in acetone but takes much longer than gel — file the bulk down, soak, push only softened product, never pry (see the gel removal lesson). Allergy: see the allergy and chemicals lesson.
Tips
- Look at the bead you have just pressed: smooth, moist-glossy and free of pits means the ratio is right.
- Unusually cheap, no clear label, no safety data sheet: don't buy it.
Quick quiz
3 questions, 20 points for each right answer.
What does a bead that is too wet (much liquid, little powder) cause?