NailsStep-by-step practice·Lesson 18/58·4:45
Builder gel and acrylic infills: step-by-step practice
Filling a builder gel or acrylic set that has grown out for a few weeks: consultation and checks under good light, prepping the regrowth, filing away lifting, thinning the old product, blending the line, cleansing, bonder only on the regrowth, applying product and rebuilding the apex (gel and acrylic), finish filing, colour, oil and booking the next infill.
The narration is in Vietnamese (subtitles: CC button on the player). The steps below are in English.
Safety first
Bonder, primer, cure times and acrylic set times always follow the brand's instructions. Large lifting, air pockets, discolouration, pain or swollen red skin: no infill — remove everything or suggest a doctor. Use an e-file only if you have been trained. Rules differ by country.
These videos are study aids. They don't replace supervised hands-on training and they are not a professional licence. Always follow the product manufacturer's instructions and the rules where you work.
Key points to remember
- 1
Consultation and checks: wash and disinfect hands, ask about breaks, lifting or pain, then look at each nail under good light, tilting it — small lifting is often just a faint line at the edge. Large lifting, air pockets, discolouration, pain, swollen red skin: no infill. Note nails that tend to lift in the customer record.
- 2
Prep the regrowth like a fresh nail (gel polish lesson): dry prep, push back gently, remove the thin tissue on the plate, buff lightly only on the regrowth to remove the shine.
- 3
Find lifting at the cuticle and side walls and file it away until the remaining edge is bonded and flush; check again under the light. Never pick or pull. If it keeps lifting or a whole area is loose: stop, remove everything and start again (gel removal lesson).
- 4
Thin the old product: file flat on the surface, reducing the bulk, especially the old apex that moved forward; shorten if too long, keeping the shape. Never file through to the natural nail. An e-file only if trained, the bit always on the product.
- 5
Blend the line: gently file the step between old product and regrowth until it is thin and flat with no ridge you can feel; file flat, lightly, away from the skin.
- 6
Cleanse: extraction still running, brush off the dust (don't blow), wipe the whole nail with a lint-free pad; then don't touch the nail plate.
- 7
Bonder only on the regrowth, with a small gap from the skin: for gel, the brand's base or bonder (cured or not as instructed); for acrylic, a very thin dab of primer on the natural nail only.
- 8
Builder gel: a thin layer over the whole nail to join the old product, a bead in the centre, floated towards the cuticle (a hair's width from the skin), to the sides and tip, finger turned over for a few seconds to form the apex, checked, then fully cured; if the customer feels heat, take the hand out for a few seconds and continue.
- 9
Acrylic: a small, slightly wetter first bead on the regrowth near the cuticle, pressed very thin towards the skin without touching it (if it touches, remove it at once while soft); then a bead on the stress area, blended into the old product to rebuild the apex. Let it set as the brand says; a dry click when tapped means it's ready.
- 10
Finish filing keeping the apex, refine side walls and tip, blend at the cuticle without touching natural nail or skin; check from above, the side and end-on. Colour and top as in the gel polish lesson, oil, book the next infill (gel about 3–4 weeks, acrylic about 2–3 weeks) and tell the customer to come back if it lifts, never peel it off.
Tips
- After filing the lifting, tilt the nail under the light: a faint white line at the edge means it's still lifting — keep filing, don't cover it.
- In VaraaAi, create separate “Gel infill” and “Acrylic infill” services with your real durations, so the calendar doesn't overlap when customers book infills.
Quick quiz
3 questions, 20 points for each right answer.
Where does the bonder (base, bonder or primer) go in an infill?