VaraaAi
Academy

HairStep-by-step practice·Lesson 44/68·5:25

Men's haircut basics: step-by-step practice

A classic short men's cut step by step: preparation and neck strip, consultation, dampening, sides and back with a clipper guard, scissor-over-comb to blend upwards, cutting the top with a guideline and cross-checking, blending the top into the sides, outlining ears, sideburns and nape, brushing off, styling, the hand mirror, notes and clean-up.

Speed

The narration is in Vietnamese (subtitles: CC button on the player). The steps below are in English.

Safety first

Guard numbers differ by brand: always start with a longer guard. Go shorter or remove the guard at the bottom edge only when agreed with the customer. Clipper blades, guards, combs and scissors are cleaned and disinfected after every customer as the product instructs; neck strips and razor blades are single-use (lesson “Tools after every customer”). Wounds, inflammation or head lice on the scalp: no cut. Rules differ by country.

These videos are study aids. They don't replace supervised hands-on training and they are not a professional licence. Always follow the product manufacturer's instructions and the rules where you work.

Key points to remember

  1. 1

    Wash your hands; clipper, guards, combs and scissors cleaned and disinfected. A single-use neck strip first, then the cape.

  2. 2

    Consult (Consultation and sectioning lesson): how short the sides, how much on top, square or rounded nape, sideburn length; what the customer disliked last time. Agree with a guard or your fingers; look for whorls and check the scalp.

  3. 3

    Dampen evenly with a fine mist while combing, never dripping (many barbers clip on clean dry hair — what matters is combed, tangle-free hair).

  4. 4

    Sides and back: the agreed guard or longer, flat at the hairline, up against the growth, slowly, overlapping; flick the wrist out at the parietal ridge; fold the ear gently; at the back from the nape to the occipital bone; go over again in another direction. Never press hard.

  5. 5

    A shorter guard or no guard at the bottom edge only if agreed beforehand — short can't be made long again.

  6. 6

    Scissor-over-comb to blend upwards: comb close to the head where the clipper stopped, teeth angled slightly out, blade parallel to the comb; the comb moves up and gradually out, never pausing.

  7. 7

    The top: section from both front corners back to the crown; the first section at the front lifted to 90° between index and middle finger and cut to length — that's the guideline; each next section takes a little of the previous, same elevation; leave more at the whorl with light tension; check with the customer midway.

  8. 8

    Cross-check the top with sections across the head from side to side; trim anything that sticks out. Blend the top into the sides at the corner with scissor-over-comb or by cutting the corner out, until no step is felt; check in profile.

  9. 9

    Outline: fold the ear, follow the natural curve, not too high; level sideburns (head straight, looking in the mirror, two fingers comparing); a square or rounded nape as agreed, head slightly forward, without pushing the line up too high.

  10. 10

    Finish: brush off loose hair with a neck brush, remove the strip; style it the way the customer will at home and show how; the hand mirror for the back, adjust at once if asked. Note guards, lengths and nape shape in the record, book the next visit in about 3–5 weeks; clean, disinfect and oil the clipper.

Tips

  • After one pass with the clipper, comb the hair down and go over it again in another direction — no flattened hairs get missed.
  • In VaraaAi, record the guards and lengths in the customer notes; next time the customer only needs to say “same as last time”.

Quick quiz

3 questions, 20 points for each right answer.

Question 1/3

How do you clip the sides evenly with a guard?